AS/NZS 3744.2:1998 (R2013) pdf free.Furniture - Assessment of the ignitability of upholstered furniture - Part2:Ignition source - Match-flame equivalent. AS/NZS 3744.2 is one of a series of standards concerned with the ignitability of upholstered furniture using various ignition sources. The ignition source used in this part of ISO 8191 is a gas flame which is equivalent to a match flame....
AS 1774.4.3-1998 (R2013) pdf free
AS 1774.4.3-1998 (R2013) pdf free.Refractories and refractory materials - Physical test methods - Part4.3:Preparation of test pieces - Unshaped refractories on site. This Standard describes the procedure for the preparation of’ test blocks on site from all types of unshaped refractory materials. NOTE: The values obtained from test pieces prepared using this method may not correspond with those obtained from...
AS/NZS 3744.3:1998 (R2013) pdf free
AS/NZS 3744.3:1998 (R2013) pdf free.Furniture - Assessment of the ignitability of upholstered furniture - Part3:Ignition sources - Nominal 160 mL/min gas flame and nominal 350 mL/min gas flame. 1 SCOPE This Standard sets out test methods to assess the ignitability of material combinations such as covers and fillings used in upholstered seating, when subjected to as flame ignition sources greater...
AS 2113.2-1998 (R2013) pdf free
AS 2113.2-1998 (R2013) pdf free.Oil of Australian eucalyptus - Part80:80 to 85% cineole. This specification lays down certain characteristics of oil of eucalyptus of 80 to 85 percent cineole content. 3 DEFINITIONS For the purpose of this Standard, the definitions below apply. 3.1 Oil of Australian eucalyptus-the oil obtained by the steam distillation from foliage and branchlets of any suitable...
AS 4359.2-1998 (R2013) pdf free
AS 4359.2-1998 (R2013) pdf free.Insulating refractory ceramic fibres - Part2:Board. I SCOPE This Standard specifies requirements for the classification and designation of insulating refractory ceramic fibre board. It does not apply to'glass'， rockwool or mineral insulating materials. 2 REFER ENCED DOCUMENTS The following documents are referred to in this Standard: AS 1774 Refractories and refractory materials-Physical test methods 774.5 Method...
AS 10303.1-1998 (R2013) pdf free
AS 10303.1-1998 (R2013) pdf free.Industrial Automation Systems And Integration - Product Data Representation And Exchange - Part1:Overview And Fundamental Principlesd. This part of Iso 10303 provides an overview of this International Standard. This International Standard provides a rcprescntation of product information along with the necessary mechanisms and definitions to enable product data to be exchanged. The exchange is among different...
AS 1019-2000 pdf free
AS 1019-2000 pdf free.Internal Combustion Engines - Spark Emission Control Devices. This Standard specifies requirements for the materials, design. construction and performance of spark arresters for controlling the emission of sparks from internal combustion engines. A method of testing the performance of spark arresters is set out in Appendix A. This Standard does not cover the following: (a) The risk...
AS 1004.2-1998 pdf free
AS 1004.2-1998 pdf free.Surface Plates For Metrology - Part2:Granite. This part of ISO 8512 specifies requirements for rectangular or square granite surface plates ranging from 160 mm x 100 mm to 2500 mm x 1600 mm, as preferred sizes, in four grades of accuracy 0, 1, 2 and 3. NOTE 1 Granit& is a commonly used description; a more specific...
AS 1004.1-1998 pdf free
AS 1004.1-1998 pdf free.Surface plates for metrology - Part1:Cast iron. This part of ISO 8512 specifies requirements for rectangular or square cast iron surface plates ranging from 160 mm x 100 mm to 2 500 mm x 1 600 mm, as preferred sizes, in four grades of accuracy 0, 1, 2 and 3. This part of ISO 8512 applies to...
AS 1001-1970 pdf free
AS 1001-1970 pdf free.Plain Setting Rings For Internal Measuring Equipment. 1 SCOPE. This standard relates to plain setting rings primarily intended for use in setting internal diameter measuring equipment. The standard covers metric rings in the range from 2 mm to 150 mm, and provides for three grades of accuracy, viz, AA, A and B. It specifies material for the...