AS/NZS 4456.11:2003 pdf.Masonry units and segmental pavers and flags - Methods of test Part11:Determining coefficients of expansion. This Standard sets out the methods for determining the coefficients of expansion of masonry units, segmental payers and flags. The coefficients of expansion estimated by these tests represent the total 15 year expansion of either kiln-fresh or non-kiln-fresh fired clay units. Provision is...
AS 5200.458-2008 pdf free
AS 5200.458-2008 pdf free.Plumbing And Drainage Products - Universal Plastic-Bodied Transition Couplings. This Standard sets out requirements for plastic-bodied transition couplings intended to join PE, P13. PEX. PP. PVC, ABS. copper, ductile iron, cast iron, lead, stainless steel and galvanized steel pipes for cold water applications (with a maximum operating pressure of 1250 kPa at 20°C) to each other and...
AS 5079.1-2003 (R2014) pdf free
AS 5079.1-2003 (R2014) pdf free.Filing Cabinets - Part1:Lateral Filing Cabinets. This standard is intended to provide manufacturers, specifiers, and users with a common basis for evaluating the function, safety, durability, and structural adequacy of free-standing lateral files. The standard defines specific tests, the laboratory equipment, and the test conditions. It specifies the acceptance levels to evaluate these products, independent of...
AS 4459.10-1999 (R2017) pdf free
AS 4459.10-1999 (R2017) pdf free.Methods Of Sampling And Testing Ceramic Tiles - Method10:Determination Of Moisture Expansion. 1 Scope This part of ISO 10545 specifies a method for determining the moisture expansion of ceramic tiles. 2 Definition For the purposes of this part of ISO 10545, the following definition applies. 2.1 Moisture expansion: Proportional accelerated expansion that results from subjecting reheated...
AS 4070-1992 (R2015) pdf free
AS 4070-1992 (R2015) pdf free.Recommended practices for protection of low-voltage electrical installations and equipment in MEN systems from transient overvoltages. This Standard recommends a simple system of insulation coordination for nominal 240/415 V. 50 Hz electrical installations in multiple earthed neutral (MEN) systems to avoid damage to wiring and equipment due to transient voltages exceeding 2500 V caused by lightning...
AS 3558.10-1999 (R2016) pdf free
AS 3558.10-1999 (R2016) pdf free.Methods of testing plastics and composite materials sanitary plumbing fixtures - Method10:Determination of thermal expansion under load of laundry troughs. 1 SCOPE This Standard sets out a method for determining the limits of thermal expansion under load of plastics laundry troughs. 2 PRINCIPLE The trough is mounted in accordance with the installation instructions. Marks are scribed...
AS 2205.7.2-2003 pdf free
AS 2205.7.2-2003 pdf free.Methods for destructive testing of welds in metal - Method7.2:Dropweight fracture toughness test for nil-ductility transition temperature. This Standard sets out a method for dropweight testing of a welded joint to determine the nil-ductility transition temperature of a selected area of metal in the weld zone. NOTE: For the purposes of this Standard, welding consumables are taken...
AS 1774.11:2015 pdf free
AS 1774.11:2015 pdf free.Refractories and refractory materials - Physical test methods, Method 11: Determination of thermal expansion. This International Standard specifies test methods for the thermal expansion of refractory products. It describes a method for determining the linear thermal expansion percentage, the linear thermal expansion curve, and the linear thermal expansion coefficient. This International Standard includes the following three test...
AS 1742.12-2000 pdf free
AS 1742.12-2000 pdf free.Manual of uniform traffic control devices - Part12: Bus, transit, tram and truck lanes. AS 1742.12-2000 specifies the traffic control devices required to designate traffic lanes as bus lanes, transit lanes, tram lanes or truck lanes. It also specifies devices for the control or prohibition of truck or bus traffic where required Ofl roadways. 2 OBJECTIVE The...
AS ISO/ASTM 52921:2020 pdf free – Standard terminology for additive manufacturing – Coordinate systems and test methodologies
AS ISO/ASTM 52921:2020 pdf free.Standard terminology for additive manufacturing - Coordinate systems and test methodologies. 1.1 This terminology includes terms, definitions of terms, descriptions of terms, nomenclature, and acronyms associated with coordinate systems and testing methodologies for additive manufacturing (AM) technologies in an effort to standardize terminology used by AM users, producers, researchers. educators, press/media. and others, particularly when reporting...