BS 5452:1977 pdf free.Specification for hospital hollow-ware made of plastics material. BS 5452 specifies requirements for hospital hollow-ware made of plastics materials. 4 Materials The hollow-ware shall be made from suitable plastics material, which shall comply with the requirements of clauses 10 and 11. 5 Design 5.1 General 5.1.1 The design shall be such as to prevent utensils from jamming...
BS 6479:1984 pdf free
BS 6479:1984 pdf free.Method for determination and verification of the effective depth of carburized and hardened cases in steels. BS 6479 describes a method for determining and verifying the effective depth of carburized and hardened cases in steels. It is applicable to: a) carburized cases including carbo-nitrided cases in steels, the depth of which is greater than 0.3 mm; h)...
BS 31100:2008 pdf free
BS 31100:2008 pdf free.Risk management - Code of practice.Here is the part of the introduction: Organizations of all types and sizes face a range of risks affecting the achievement of their objectives. While “risk” is commonly regarded as negative, risk management is as much about exploiting potential opportunities as preventing potential problems. It is important to bear this in mind...
en 14566 pdf
BS EN 14566:2008 PDF FREE.MECHANICAL FASTENERS FOR GYPSUM PLASTERBOARD SYSTEMS - DEFINITIONS, REQUIREMENTS AND TEST METHODS. BS EN 14566 specifies the characteristics and performance of mechanical fasteners, including nails, screws and staples, intended to be used for the fixing of gypsum plasterboard, gypsum boards with fibrous reinforcement, products from secondary processing and suitable ancillary products as shown in Figure 2,...
BS EN ISO 7225:2007 pdf free
BS EN ISO 7225:2007 pdf free.Gas cylinders — Precautionary labels. Introduction BS EN ISO 7225 belongs to a series of standards specifying gas cylinder identification requirements: — ISO 13769, Gas cylinders — Stamp marking ISO 7225, Gas cylinders — Precautionary labels - ISO 32, Gas cylinders for medical use — Marking for identification of content The purpose of using precautionary...
iso 3245 pdf
BS ISO 3245-2007.Rolling Bearings - Needle Roller Bearings, Drawn Cup Without Inner Ring - Boundary Dimensions And Tolerances. ISO 3245:2007 specifies the boundary dimensions and preferred dimensions to be used for drawn cup needle roller bearings without inner ring as well as the minimum chamfer dimension limits. Also specified are the closed end thickness dimensions for bearings with closed end...
BS 6280:1982 pdf free
BS 6280:1982 pdf free.Method of vacuum (backsiphonage) test for water-using appliances. This British Standard BS 6280 describes a method for applying a vacuum test to water-using appliances to determine that they have an acceptable degree of protection against backflow or backsiphonage. NOTE The titles of the publications referred to in this standard are given on the inside back cover. 2...
BS 6320:1982 pdf free
BS 6320:1982 pdf free.Specification for modems for connection to the British Telecommunications public switched telephone network. This British Standard BS 6320 specifies requirements for modems and associated call-set-up equipment for connection at an NTTF or through an NTTP port to the British Telecommunications pub>ic switched telephone network (PSTN). The standard applies both to self-contained modems and also to modems incorporated...
BS 6522:1984 pdf free
BS 6522:1984 pdf free.Methods for determination of percentage water saturation of insulating oil. This British Standard BS 6522 describes a method of test for the determination of the percentage water saturation of insulating oil. The method and apparatus described enables the percentage saturations of oil to be determined at temperatures up to 60 °C provided the dew-point does not exceed...
BS 6466:1984 pdf free
BS 6466:1984 pdf free.Code of practice for design and installation of ceramic fibre furnace linings. This code of practice recommends good working practice for the design and installation of insulating linings for furnaces where ceramic fibrous materials comprise the whole or a significant part of the lining. The code is concerned with furnaces generally operating at temperatures of 800 °C...