BS EN 200:2008 pdf free.Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification. In respect of potential adverse effects on the quality of water intended for human consumption, caused by the product covered by this European Standard. BS EN 200 provides no information as to whether the...
BS EN 980:2008 pdf free
BS EN 980:2008 pdf free.Symbols For Use In The Labelling Of Medical Devices. BS EN 980 has been prepared to give expression to the legislative preference within the European Union for the use of symbols in medical device labelling, thereby reducing the need for multiple translations of words into national languages. It is also intended to simplify labelling wherever possible...
BS 8509:2008 pdf free
BS 8509:2008 pdf free.Children's Beds For Domestic Use - Safety Requirements And Test Methods. BS 8509 specifies requirements for the safety of children’s beds for domestic use with a maximum internal width of 1 000 mm and a maximum height of bed base of 400 mm. The requirements apply to children’s beds that are fully assembled and ready for use....
BS EN 993-11:2007 pdf free
BS EN 993-11:2007 pdf free.Methods of test for dense shaped refractory products - Part11:Determination of resistance to thermal shock. Introduction Thermal shock of refractory materials used in furnaces is influenced by three main factors: - brick dimensions; - heating/cooling conditions; - material properties. Thermal shock tests are usually intended to test material properties. This is done by standardizing brick dimensions...
BS 957:2008 pdf free
BS 957:2008 pdf free.Specification for feeler gauges.The introduction of BS 957: BS 957 specifies requirements for feeler gauges, comprising a series of gauging blades (blades) of graded thicknesses assembled in a protective sheath or supplied individually. These include requirements for dimensions which are expressed in metric and inch units. This standard is applicable to blades of thicknesses: • from 0.03...
BS EN ISO 4672:1999 pdf free
BS EN ISO 4672:1999 pdf free.Rubber and plastics hoses - Sub-ambient temperature flexibility tests. BS EN ISO 4672d specifies two methods for assessing whether a rubber or plastics hose retains adequate flexibility at sub-ambient temperatures. Method A is applicable to non-collapsible hose with a nominal bore up to and including 25. It measures the increase in stiffness compared to the...
BS EN ISO 10093:1999 pdf free
BS EN ISO 10093:1999 pdf free.Plastics - Fire tests - Standard ignition sources. Introduction Fires are caused by a wide range of possible ignition sources. Statistical analysis of fires has identified the main primary and secondary sources, especially for fires in buildings. The most frequent sources of fires have been found to be as follows: a) cooking appliances; b) space-heating...
BS EN ISO 2554:1999 pdf free
BS EN ISO 2554:1999. Plastics - Unsaturated polyester resins - Determination of hydroxyl value. BS EN ISO 2554 specifies a method for determining the hydroxyl value of unsaturated polyester resins. In fact, this method determines the difference between the hydroxyl value and t.he acid value; it is therefore necessary t.o determine the total acid value separately, in order to calculate...
BS EN ISO 8560:1999 pdf free
BS EN ISO 8560:1999 pdf free.Construction drawings - Representation of modular sizes, lines and grids. BS EN ISO 8560 lays down rules for the representation of modular sizes, lines and grids on construction drawings. The basic module M is 100 mm (see ISO 1006). Generally, modular sizes should be used on design drawings. Construction and work sizes should be used...
BS EN ISO 7808:1999 pdf free
BS EN ISO 7808:1999 pdf free.Plastics - Thermosetting moulding materials - Determination of transfer flow. BS EN ISO 7808 specifies a method for measuring the transfer flow of thermosetting moulding materials during a specified moulding process. It is intended only for production control and should not be used as part of a mandatory material specification. 2 Principle The method determines...