BS pdf free download - Page 16 of 117

BS ISO 473:2019 pdf free

BS ISO 473:2019 pdf free.Lithopone pigments - General requirements and methods of testing. Weigh, to the nearest 0,1 mg, about 0,6 g of lithopone 30 %, or about 0,3 g of lithopone 60 %, or about 0,6 g of lithopone 20 %, all previously dried at (105 ± 2) °C, into a beaker and add 25 ml of the hydrochloric...

06-07

Download

BS EN 12350-4:2019 pdf free

BS EN 12350-4:2019 pdf free.Testing fresh concrete. 4 Principle Carefully place the fresh concrete in a compaction container using a trowel, avoiding any compaction of the concrete. When the compaction container is full, the top surface is struck off level with the top of the compaction container. The concrete is compacted by vibration and the distance from the surface of...

06-07

Download

BS EN 9138:2019 pdf free

BS EN 9138:2019 pdf free.Aerospace Series一Quality Management Systems一Statistical Product一Acceptance Requirements. 2 Normative references The following referenced documents are valuable for the application of specific tools presented in this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. When a conflict in requirements between this document and...

06-07

Download

BS EN 2288:2019 pdf free

BS EN 2288:2019 pdf free.Aerospace series - Bush, flanged, corrosion resisting steel, with self-lubricating liner - Dimensions and loads. 1 Scope This European standard specifies the characteristics of flanged bushes in corrosion resisting steel with self-lubricating liner and the design recommendation of shafts and housings. The bushes are intended for operation within the temperature range of -55 °C to 163...

06-07

Download

BS EN 131-6:2019 pdf free

BS EN 131-6:2019 pdf free.Ladders. 4 Functional dimensions 4.1 General dimensions Dimensions are given in EN 131-1. 4.2 Specific dimensions For leaning telescopic ladders dimension l3 is not applicable providing l6, see 4.3, is fulilled. If l6 is not fulflled l3 shall begreater than 0,5 I5 and less than I5 + 15 mm measured along a line in the middle...

06-07

Download

BS EN 2959:2019 pdf free

BS EN 2959:2019 pdf free.Aerospace series-H eat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) - Solution treated and cold worked-Bar for forged fasteners-3 mm≤D≤30 mm. 1 Scope This document specifies the requirements relating to: Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) Solution treated and cold worked Bar for forged fasteners 3mm≤D≤30mm for aerospace applications.2 Normative references The following documents are referred to in the text...

06-07

Download

BS EN 2876:2019 pdf free

BS EN 2876:2019 pdf free.Aerospace series-Nuts, hexagon, plain, reduced height, normal across flats, in aluminium alloy, anodized - Classification:450 MPa threads - Part 2: Limit dimensions for bolts and nuts ISO 8788, Aerospace - Nuts, metric - Tolerances of form and position ISO 9139, Aerospace一Nuts, plain or slotted (castellated) - Procurement specification ISO 9609, Aerospace - - Nuts, hexagonal, plain,...

06-07

Download

BS EN 4612-005:2019 pdf free

BS EN 4612-005:2019 pdf free.Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family- Jacketed or screened and jacketed. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies....

06-06

Download

BS EN 3460:2019 pdf free

BS EN 3460:2019 pdf free.Aerospace series - Titanium TI-P99002 - Annealed - Bar for machining-a or D ≤ 150 mm- Rm ≥ 390 MPa. 1 Scope This document specifies the requirements relating to: Titanium TI-P99002 Annealed Bar for machining aorD ≤ 150mm Rm ≥ 39OMPa for aerospace applications. 2 Normative references The following documents are referred to in the text...

06-06

Download

BS EN 3220:2019 pdf free

BS EN 3220:2019 pdf free.Aerospace series - Heat resisting nickel base alloy (Ni-P101HT) - Cold worked and softened - Bar and wire for continuous forging or extrusion for fasteners- 3 mm ≤ D ≤ 30 mm. 1 Scope This document specifies the requirements relating to: Heat resisting nickel base alloy (Ni-P101HT) Cold worked and softened Bar and wire for continuous...

06-06

Download