BS ISO 3140:2019 pdf free.Essential oil of sweet orange expressed The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/TS 210, Essential...
BS ISO 516:2019 pdf free
BS ISO 516:2019 pdf free.Camera shutters - Timing - General definition and mechanical shutter measurements. The method described for each type of shutter, based on digital readout, is rapid and easy for routine manufacturing testing and quality control. As a rule, this method is applicable only to cases in which the character of the time-illuminance curve of the shutter has...
BS ISO 21250-1:2020 pdf free
BS ISO 21250-1:2020 pdf free.Rolling bearings一Noise testing of rolling bearing greases. In the case of grease lubrication, many factors can affect the degree of cleanliness during operation. For the initial lubrication and relubrication, clean grease is always required. Also, in applications where the fatigue life is not an issue e.g. at very low load), the use of clean greases can...
BS ISO 20890-3:2020 pdf free
BS ISO 20890-3:2020 pdf free.Guidelines for in-service inspections for primary coolant circuit components of light water reactors. The system pressure test provides a global statement of integrity regarding the reactor coolant system and, as a safety measure for monitoring the consequences of alleged operationally induced damage mechanisms, is a part of the concept for assuring component integrity during operation. A...
BS ISO 20890-2:2020 pdf free
BS ISO 20890-2:2020 pdf free.Guidelines for in-service inspections for primary coolant circuit components of light water reactors. NDT personnel have a great responsibility, not only with respect to their employers or contractors but also under the rules of good workmanship. The NDT personnel shall be independent and free from economic influences with regard to his test results, otherwise the results...
BS ISO 20816-9:2020 pdf free
BS ISO 20816-9:2020 pdf free.Mechanical vibration——Measurement and evaluation of machine vibration. The vibrations of a gear unit can be measured in two ways, i.e. on the housing values of vibration velocity in millimetres per second and the true peak values of vibration acceleration in metres per second per second. The mounting method can affect the frequency response of the transducer;...
BS ISO 20771:2020 pdf free
BS ISO 20771:2020 pdf free.Legal translation - Requirements. Legal translation is a specialization which covers law-related or legal specialist field translation in terms of content as well as context (e.g. legal settings). Given the highly specialist field, potential legal consequences of mistranslation, and formal and liability issues, legal translation requires specific competences and qualifications and a very professional approach from...
BS ISO 20766-11:2020 pdf free
BS ISO 20766-11:2020 pdf free.Road vehicles一Liquefied petroleum gas (LPG) fuel systems components. The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO...
BS ISO 20468-3:2020 pdf free
BS ISO 20468-3:2020 pdf free.Guidelines for performance evaluation of treatment technologies for water reuse systems. Depending on the water treatment efficiency and performance to be achieved, pre-treatment and/or post-treatment can be added to the ozone system. For example, sand filtration as the typical pretreatment process to remove suspended impurities including ozone scavengers and inorganic matter enhances treated water quality and...
BS ISO IEC 23396:2020 pdf free
BS ISO IEC 23396:2020 pdf free.Systems and software engineering一Capabilities of review tools. IssueByReview in this object model (hereinafter referred as IssueByReview) is an entity representing an issue which is identified in the review. NOTE1 Issue is defined in ISO/IEC 20246. PlaceOfIssueByReview in this object model (hereinafter referred as PlaceOflssueByReview) is an entity representing a place where the issue is identified....