BS pdf free download - Page 29 of 117

BS ISO 6721-9:2019 pdf free

BS ISO 6721-9:2019 pdf free.Plastics一Determination of dynamic mechanical properties. Apply a sonic pulse to the specimen, and measure the arrival time tA (s) to an accuracy of士0,5 us.Repeat the measurements described in 9.3.1 and 9.3.2 for the same specimen at least three different separation distances between the transducers. In order to get good accuracy, the values of the distance should...

05-22

Download

BS ISO 5355:2019 pdf free

BS ISO 5355:2019 pdf free.Alpine ski-boots一Requirements and test methods. When the front bearing surface rests on a plane, a gauge 1 mm thick and 10 mm wide shall not enter the AB area at any point. See Figure 3.When the rear bearing surface rests on a plane, a gauge 1 mm thick and 10 mm wide shall not enter the...

05-22

Download

BS ISO 11525-1:2020 pdf free

BS ISO 11525-1:2020 pdf free.Rough-terrain trucks - Safe use requirements. This document shall be supplemented by good management practices, safety controls and application of sound principles of safety, training, inspection, maintenance, application selection and operation. All data available regarding the parameters of intended use and expected environment shall be considered. Those with direct control over the application and operation of...

05-22

Download

BS ISO 10968:2020 pdf free

BS ISO 10968:2020 pdf free.Earth-moving machinery一Operator's controls. The type, location and method of operation of typical primary controls shall be according to Annex A for base machine movements, according to Annex B for equipment movements, and according to Annex C for attachment movements. Specific requirements for graders are found in Annex D. Specific requirements for dozers are found in Annex...

05-22

Download

BS ISO 9523:2019 pdf free

BS ISO 9523:2019 pdf free.Touring ski-boots for adults一Interface with touring ski-bindings一Requirements and test methods. The sole dimensions in the toe and heel boot binding interface areas shall be symmetrical about the median plane within an admissible deviation of 1 mm. There shall be no protrusion of the sole beyond the shell for the whole perimeter of the whole boot sole...

05-22

Download

BS ISO 21406:2020 pdf free

BS ISO 21406:2020 pdf free.Tourism and related services一Yacht harbours一Essential requirements for luxury harbours. The luxury yacht harbour shall have access control effective 24 h a day, 7 days a week. Access controls such as key pads and swipe cards shall be accessible and within reach of persons with physical disabilities, and provide both audible and visual confirmation when access is...

05-22

Download

BS ISO 21322:2020 pdf free

BS ISO 21322:2020 pdf free.Cosmetics - Microbiology - Testing of impregnated or coated wipes and masks. The method determines the population of viable microorganisms by enumeration of colonies on a non-selective agar medium and by the presence or absence of specified microorganisms growth after enrichment. The method involves the following steps:selection of the test sample; selection of an appropriate method;...

05-22

Download

BS ISO 24497-1:2020 pdf free

BS ISO 24497-1:2020 pdf free.Non-destructive testing一Metal magnetic memory. Equipment and structures (IOs) should be inspected by MMM in in-service state (under load) as well as in the maintenance state (after removal of operating loads). If possible, the initial magnetic service state of the I0 should be determined.Surface dressing and preparation are not required. It is recommended to remove insulation to...

05-22

Download

BS ISO 24018:2020 pdf free

BS ISO 24018:2020 pdf free.Jewellery and precious metals -Specifications for 1 kilogram gold bar. Bars should have flat and smooth surfaces (a small shrinkage on the top surface is acceptable), and be free from cavities, holes, and significant layering. Edges shall not be sharp and pose a handling hazard. There is no specification for the internal quality, but the presence...

05-22

Download

BS ISO 23354:2020 pdf free

BS ISO 23354:2020 pdf free.Business requirements for end-to-end visibility of logistics flow. Data providers can share/obtain data to/from connected LISS directly and to/from other LISSS indirectly. Data users can obtain data from multi-LISSs directly or indirectly.The detailed network architecture requirements are specified in Clause 6.Visibility data interchange requirements between LISSS.Data interchange should be neutral, trusted and controlled. Event data should...

05-22

Download