ISO pdf free download - Page 2 of 19

ISO 24613-4:2021 pdf free download

ISO 24613-4:2021 pdf free download.Language resource management一 Lexical markup framework (LMF) 一Part 4: TEI serialization. Unless explicitly stated, all resulting constructs shall be valid TEl representations, which means that the specification described in this document corresponds to a pure subset of the TEl Guidelines. They shall thus be well-formed XML documents as specified by the W3C XML recommendation. This document...

10-02

Download

ISO 10993-12:2021 pdf free download

ISO 10993-12:2021 pdf free download.Biological evaluation of medical devices - Part 12: Sample preparation and reference materials. 5 Reference materials (RMs) 5.1 General RMs are established by individual laboratories. The extent of chemical, physical and biological characterization is determined by the individual laboratory. Commercially available articles may be used as RMs. NOTE See also ISO Guide 35. CRMs are selected...

10-02

Download

ISO 12671:2021 pdf free download

ISO 12671:2021 pdf free download.Thermal spraying一Thermally sprayed coatings一Symbolic representation on drawings. 8 Instructions when using a separate parts’ list This clause applies when a component is represented by one or more drawings and a separate parts’ list. In such a case, the coating will be indicated on the drawing only by a position number (see Figure 6). Any instructions regarding...

10-02

Download

ISO 15854:2021 pdf free download

ISO 15854:2021 pdf free download.Dentistry一Casting and baseplate waxes. 5.6 Behaviour on softening (Type 2) The wax shall soften without becoming sticky or crumbly and shall be mouldable without breaking or delaminating when tested in accordance with 4. This requirement shall not apply to baseplate preforms where a suitable square test piece cannot be cut. 5.7 Residue on artificial teeth (Type...

10-02

Download

ISO 19905-3:2021 pdf free download

ISO 19905-3:2021 pdf free download.Petroleum and natural gas industries一Site-specific assessment of mobile offshore units - Part 3: Floating units. 5.2 Assessment The objective of the assessment is to show that the acceptance criteria are met. Annex B provides a diagrammatic example of the process to be used in the site-specific assessment of a mobile floating unit. Other approaches may be...

10-02

Download

DIN ISO 4593:2019 pdf free

DIN ISO 4593:2019 pdf free.Plastics - Film and sheeting - Determination of thickness by mechanical scanning (ISO 4593:1993). 3 Test specimens Cut test specimens, about 100 mm wide, across the whole width of the sample. When required, take specimens at positions approximately 1 m apart in the longitudinal direction of the sample. The specimens shall contain no creases except those...

08-10

Download

DIN EN ISO 846:2019 pdf download

DIN EN ISO 846:2019 pdf download.Plastics - Evaluation of the action of microorganisms (ISO 846:2019). 4 Kurzbeschreibung 4.1 Allgemeines Zur Prüfung werden die Prütkorper aus Kunststoff der Einwirkung von ausgewählten Teststämmen von Plizen und Bakterien (oder, beim Erdeingrabeversuch, mikrobiell aktiver Erde) über festgelegte oder vereinbarte Zeitspannen und unter festgelegten Klimabedingungen (Temperatur und Luftfeuchte) ausgesetzt. Nach Ende der Einwirkung werden die...

08-10

Download

ISO 6721-6:2019 pdf free

ISO 6721-6:2019 pdf free.Plastics — Determination of dynamic mechanical properties — Part 6: Shear vibration — Non-resonance method. ISO 6721-6 describes a forced, non-resonance method for determining the components of the shear complex modulus G* of polymers at frequencies typically in the range 0,01 Hz to 100 Hz. Higher-frequency measurements can be made, but significant errors in the dynamic properties...

04-20

Download

ISO 20078-3:2019 pdf free

ISO 20078-3:2019 pdf free.Road vehicles — Extended vehicle (ExVe) web services — Part 3: Security. ISO 20078-3 defines how to authenticate users and Accessing Parties on a web services interface. It also defines how a Resource Owner can delegate Access to its Resources to an Accessing Party. Within this context, this document also defines the necessary roles and required separation...

04-20

Download

ISO 11971:2020 pdf free

ISO 11971:2020 pdf free.Steel and iron castings — Visual testing of surface quality. ISO 11971 covers the acceptance criteria for the visual testing of the surface of steel and iron castings. Introduction The surface roughness of a casting is influenced by the manufacturing process (moulding, grinding, finishing, etc.), the moulding materials used (sand, coating. etc.), the equipment available and the...

04-20

Download