ISO 3994:2007 pdf free.Plastics hoses — Helical-thermoplastic-reinforced thermoplastics hoses for suction and discharge of aqueous materials — Specification. ISO 3994 has been prepared to provide minimum acceptable requirements for the satisfactory performance of polymer-reinforced thermoplastics hoses for suction and discharge applications, conveying water, weak aqueous chemical solutions and abrasive solids and slurries. If there is a special requirement for resistance...
ISO 9058:2008 pdf free
ISO 9058:2008 pdf free.Glass containers — Standard tolerances for bottles. This International Standard specifies tolerances for glass bottles of circular cross-section and nominal capacity from 50 ml to 5000 ml. NOTE This International Standard is based on CE.T.I.E data sheet DT 2 (1996) and EC Council Directive 75/107/EEC. 2 Normative references ISO 7348:1992, Glass containers — Manufacture — Vocabulary ISO...
ISO 9587:2007 pdf free
ISO 9587:2007 pdf free.Metallic and other inorganic coatings — Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement. ISO 9587:2007 establishes stress-relief requirements for high strength steels, in order to reduce their susceptibility or degree of susceptibility to hydrogen embrittlement in subsequent pretreatment, electroplating, autocatalytic plating, chemical conversion and phosphating processes. This International Standard is applicable to...
ISO 7197:2006 pdf free
ISO 7197:2006 pdf free.Neurosurgical implants — Sterile, single-use hydrocephalus shunts and components. A shunt is defined as an artificial connection of two compartments inside the body. For the treatment of hydrocephalus, the ventriculo-atrial shunt has been introduced initially to control the intraventricular pressure in the brain of the patients. Today ventriculo-peritoneal shunts are preferably implanted. In special cases, a lumbo-peritoneal...
ISO 3733:1999 pdf free
ISO 3733:1999 pdf free.Petroleum products and bituminous materials — Determination of water — Distillation method. ISO 3733 specifies a method for determination of water up to 25 % in petroleum products, bitumens, tars and products derived from these materials, excluding emulsions, by the distillation method. The specific products considered during the development of this test method are listed in Table...
ISO 5596:1999 pdf free
ISO 5596:1999 pdf free.Hydraulic fluid power — Gas-loaded accumulators with separator — Ranges of pressures and volumes and characteristic quantities. Introduction of ISO 5596: In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. Gas-loaded accumulators are components that are able to store and return energy in accordance with the principle...
ISO 5858:1999 pdf free
ISO 5858:1999 pdf free.Aerospace — Nuts, self-locking, with maximum operating temperature less than or equal to 425 degrees C — Procurement specification. ISO 5858 specifies the required characteristics for metric self-locking nuts, with MJ threads, for use in aerospace construction at a maximum temperature less than or equal to 425 °C. ISO 5858 is applicable to nuts as defined above,...
ISO 8018:2007 pdf free
ISO 8018:2007 pdf free.Tools for moulding — Guide bushes, headed, and locating guide bushes, headed. ISO 8018 specifies the dimensions and tolerances, in millimetres, for headed guide bushes and headed locating guide bushes intended for use in moulds. 2 Dimensions 2.1 Guide bushes, headed — Type A The dimensions of headed guide bushes of type A shall conform to the...
ISO 8697:1999 pdf free download
ISO 8697:1999 pdf free download.Crude petroleum and petroleum products — Transfer accountability — Assessment of on board quantity (OBQ) and quantity remaining on board (ROB). ISO 8697 is intended to encourage uniformity of measurement, accounting and reporting procedures of “On Board Quantity” (OBQ) and the quantity “Remaining on Board” (ROB). All safety precautions should be in accordance with the International...
ISO 7096:2000 pdf free
ISO 7096:2000 pdf free.Earth-moving machinery — Laboratory evaluation of operator seat vibration. The operators of earth-moving machinery are often exposed to a low frequency vibration environment partly caused by the movement of the vehicles over uneven ground and the tasks carried out. The seat constitutes the last stage of suspension before the driver. To be efficient at attenuating the vibration,...