ISO PDF Download

BS ISO 13939:2019 pdf free

BS ISO 13939:2019 pdf free.Foil bearings - Performance testing of foil journal bearings一Testing of static load capacity, friction coefficient and lifetime. The test mainly aims to measure and evaluate the static load capacity, friction coefficient and lifetime of foil journal bearings. These primary performance metrics of the foil journal bearing as a mechanical element with a specific dimension are closely...

06-11

Download

BS IEC 62951-2:2019 pdf free

BS IEC 62951-2:2019 pdf free.Semiconductor devices - Flexible and stretchable semiconductor devices. The stability test of a flexible TFT is carried out using four kinds of biased evaluation. The negative-bias-stress (NBS) test is carried out with a VGs of -20 V at a fixed Vps of 10 V under dark and the substrate temperature is maintained at 20 °C and...

06-11

Download

BS ISO 7870-1:2019 pdf free

BS ISO 7870-1:2019 pdf free.Control charts. 3.1 control chart chart with control limits (3.2) on which some statistical measure of a series of samples is plotted in a particular order to steer the process with respect to that measure Note 1 to entry: The particular order is usually based on time or sample number order. Note 2 to entry: The...

06-11

Download

BS EN 50693:2019 pdf free

BS EN 50693:2019 pdf free.Product category rules for life cycle assessments of electronic and electrical products and systems. To quantify the potential environmental impacts caused by EEPS, LCA compliant with EN ISO 14040 and EN ISO 14044 shall be performed. And results can then be used to identify improvement potentials in terms of e.g. environmental conscious product design. In addition,...

06-10

Download

BS EN 50518:2019 pdf free

BS EN 50518:2019 pdf free.Monitoring and Al larm Receiving Centre. 4.1 Categorization The planning for the construction of an ARC should be determined by the intended categorization. ARC'S are categorized according to the type(s) of alarm messages handled and the consequent requirements for integrity and security of construction, communications, operation and information. This standard gives recommendations for two categories of...

06-10

Download

BS EN 2465:2019 pdf free

BS EN 2465:2019 pdf free.Aerospace series - Steel X2CrNi18-9 (1.4307)-Softened - 450 MPa≤Rm≤680 MPa- Bars for machining- 4 mm≤De≤100 mm. 1 Scope This document specifies the requirements relating to: Steel X2CrNi18-9 (1.4307) Softened 450MPa≤Rm≤680MPa Bars for machining 4mm≤De≤100mm for aerospace applications. 2 Normative references The following documents are referred to in the text in such a way that some or...

06-10

Download

BS 7858:2019 pdf free

BS 7858:2019 pdf free.Screening of individuals working in a secure environment- Code of practice. Top management should: a) be committed to satisfying the recommendations of this British Standard; b) ensure that the resources and infrastructure needed for the screening process are available; c) direct and support persons to contribute to the effectiveness of the screening process; and d) ensure that...

06-10

Download

BS ISO 355:2019 pdf free

BS ISO 355:2019 pdf free.Rolling bearings - Tapered roller bearings -Boundary dimensions and series designations. For the purposes of this document, the terms and definitions given in ISO 1132-1 and ISO 5593 apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: ISO Online browsing platform: available at https://www.iso.org/obp IEC Electropedia: available at http://www.electropedia.org/ Each bearing...

06-10

Download

BS IEC 62047-34:2019 pdf free

BS IEC 62047-34:2019 pdf free.Semiconductor devices - Micro-electromechanical devices. The test system is built in accordance with the general provisions set out in 5.1 to 5.3 and the test preparation described in 6.1. The test of the static performance shall use the five-point sampling method or be in accordance with the user requirements. As shown in Figure 3, the same...

06-10

Download

BS EN ISO 10320:2019 pdf free

BS EN ISO 10320:2019 pdf free.Geosynthetics - Identification on site (ISO 10320:2019). 3.1 supplier person or organization from which a geosynthetic is purchased or otherwise obtained Note 1 to entry: A supplier who is not the manufacturer is expected to ensure that the responsibilities of the manufacturer are fully met. 3.2 product name brand name :name given to a particular...

06-10

Download