ISO PDF Download

BS EN 131-6:2019 pdf free

BS EN 131-6:2019 pdf free.Ladders. 4 Functional dimensions 4.1 General dimensions Dimensions are given in EN 131-1. 4.2 Specific dimensions For leaning telescopic ladders dimension l3 is not applicable providing l6, see 4.3, is fulilled. If l6 is not fulflled l3 shall begreater than 0,5 I5 and less than I5 + 15 mm measured along a line in the middle...

06-07

Download

BS EN 2959:2019 pdf free

BS EN 2959:2019 pdf free.Aerospace series-H eat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) - Solution treated and cold worked-Bar for forged fasteners-3 mm≤D≤30 mm. 1 Scope This document specifies the requirements relating to: Heat resisting alloy NI-PH1302 (NiCr20Co13Mo4Ti3Al) Solution treated and cold worked Bar for forged fasteners 3mm≤D≤30mm for aerospace applications.2 Normative references The following documents are referred to in the text...

06-07

Download

BS EN 2876:2019 pdf free

BS EN 2876:2019 pdf free.Aerospace series-Nuts, hexagon, plain, reduced height, normal across flats, in aluminium alloy, anodized - Classification:450 MPa threads - Part 2: Limit dimensions for bolts and nuts ISO 8788, Aerospace - Nuts, metric - Tolerances of form and position ISO 9139, Aerospace一Nuts, plain or slotted (castellated) - Procurement specification ISO 9609, Aerospace - - Nuts, hexagonal, plain,...

06-07

Download

BS EN 4612-005:2019 pdf free

BS EN 4612-005:2019 pdf free.Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family- Jacketed or screened and jacketed. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies....

06-06

Download

BS EN 3460:2019 pdf free

BS EN 3460:2019 pdf free.Aerospace series - Titanium TI-P99002 - Annealed - Bar for machining-a or D ≤ 150 mm- Rm ≥ 390 MPa. 1 Scope This document specifies the requirements relating to: Titanium TI-P99002 Annealed Bar for machining aorD ≤ 150mm Rm ≥ 39OMPa for aerospace applications. 2 Normative references The following documents are referred to in the text...

06-06

Download

BS EN 3220:2019 pdf free

BS EN 3220:2019 pdf free.Aerospace series - Heat resisting nickel base alloy (Ni-P101HT) - Cold worked and softened - Bar and wire for continuous forging or extrusion for fasteners- 3 mm ≤ D ≤ 30 mm. 1 Scope This document specifies the requirements relating to: Heat resisting nickel base alloy (Ni-P101HT) Cold worked and softened Bar and wire for continuous...

06-06

Download

BS EN 343:2019 pdf free

BS EN 343:2019 pdf free.Protective clothing - Protection against rain. When tested in accordance with 6.2.1 the requirements according to EN ISO 13688 and the following requirements shall be met:the garment shall not have rough, sharp or hard surfaces that irritate or injure the user;all pockets shall be constructed to avoid water inside the garment;closures, such as slide fasteners, fasteners,...

06-06

Download

BS EN 687:2019 pdf free

BS EN 687:2019 pdf free.Resilient floor coverings - Specification for plain and decorative linoleum on a corkment backing. The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced...

06-06

Download

BS EN 14726:2019 pdf free

BS EN 14726:2019 pdf free.Aluminium and aluminium alloys -Determination of the chemical composition of aluminium and aluminium alloys by spark optical emission spectrometry. 7.2 Reference materials and recalibration samples The certified reference materials, the reference materials (see ISO Guide 30) and the recalibration samples should he listed and documented in a laboratory iwocedure: — certified reference materials for calibration (see...

06-06

Download

BS IEC 62047-32:2019 pdf free

BS IEC 62047-32:2019 pdf free.Semiconductor devices-Micro-electromechanical devices. 5.2 Test conditions a) Keep the ambient temperature within 23 °C ± 5 °C. b) Maintain the vacuum degree of the vacuum chamber according to the actual operation of the resonator. C) Adjust the micro-optical apparatus to restrict the laser spot within the surface of the resonator. d) For transparent resonators, the laser...

06-06

Download