ISO PDF Download

BS EN 4859:2019 pdf free

BS EN 4859:2019 pdf free.Aerospace series - Sensor based clamp load determination / high tensile bolts - Technical specification. 3.1 thin film ultrasonic transducer this kind of transducer applied to one of the two a bolt ends converts an electrical pulse in an ultrasonic wave travelling through the bolt body and transforms the reflected ultrasonic wave back into an electrical...

06-05

Download

BS ISO 21546:2019 pdf free

BS ISO 21546:2019 pdf free.Paints and varnishes - - Determination of the resistance to rubbing using a linear abrasion tester (crockmeter). A loaded abrasion tool, lined with agreed abrasive material and influenced by an agreed abrasive medium, is moved over the coating using a linear abrasion tester (crockmeter). There are three procedure variations, depending on the agreement and application (see...

06-05

Download

BS IEC 62954:2019 pdf free

BS IEC 62954:2019 pdf free.Nuclear power plants - Control rooms -Requirements for emergency response facilities. An overarching principle of this document is that the emergency plan for the nuclear power plant site (assumed to comprise one or more reactor units and associated spent fuel storage facilities) imposes overall requirements for the ERF which are further detailed in this document. This...

06-05

Download

BS EN 17176-5:2019 pdf free

BS EN 17176-5:2019 pdf free.Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-0). The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited...

06-05

Download

BS 45002-2:2019 pdf free

BS 45002-2:2019 pdf free.Occupational health and safety management systems - General guidelines for the application of ISO 45001. Context of the organization The risks and opportunities to be considered by the organization depend on the type of organization, what it does and where this is done. This is the context of the organization. For example, if the organization makes cars...

06-05

Download

BS EN 13880-7:2019 pdf free

BS EN 13880-7:2019 pdf free.Hot applied joint sealants. 4 Principle This method is intended to serve as an accelerated test for the assessment of damage to hot applied sealants resulting from fluctuating temperatures, water-spraying and simultaneous dynamic loads. 5 Apparatus 5.1 Tensile test rig, which allows the test specimens to be inserted into holding clamps, conveniently and without disturbing the...

06-05

Download

BS EN 10217-4:2019 pdf free

BS EN 10217-4:2019 pdf free.Welded steel tubes for pressure purposes -Technical delivery conditions. 7 Manufacturing process 7.1 Steelmaking process The steelmaking process is at the discretion of the manufacturer with the exception that the open hearth (Siemens-Martin) process shall not be employed unless in combination with a secondary steelmaking or ladle refining process. Steels shall be fully killed and contain...

06-05

Download

BS EN 10217-3:2019 pdf free

BS EN 10217-3:2019 pdf free.Welded steel tubes for pressure purposes -Technical delivery conditions. 7.2.1 Tube manufacturing shall be as specified in Table 1. Unless Option 1 is specified, the manufacturing process and route is at the discretion of the manufacturer. Option 1: The manufacturing process and/or route from Table 1 is specified by the purchaser. Electric welded tubes shall be...

06-05

Download

BS EN 943-2:2019 pdf free

BS EN 943-2:2019 pdf free.Protective clothing against dangerous solid, liquid and gaseous chemicals, including liquid and solid aerosols. The information supplied by the manufacturer shall comply with EN 943-1 : 2015 + A1 : 2019 , Clause 8 . The instructions for use shall also include a statement that compliance with the performance requirements of this standard do not infer...

06-05

Download

BS EN 12390:17:2019 pdf free

BS EN 12390:17:2019 pdf free.Testing hardened concrete. The loading frame shall be sufficiently rigid to ensure uniform loading of the specimen(s) and capable of applying and maintaining the required load to within ± 3 % on the specimen or group of specimens for the duration of the test, irrespective of any change in the dimension of the specimen(s). NOTE 1...

06-05

Download