BS ISO 3166-2:2020 pdf free.Codes for the representation of names of countries and their subdivisions,Country subdivision code. BS ISO 3166-2 The country subdivision names included in part 2 of the ISO 3166 database shall be those that properly reflect the subdivisions of the countries included in ISO 3166-1 of the ISO 3166 database. Names reflec the complete currently known subdivision...
BS ISO 3669:2020 pdf free
BS ISO 3669:2020 pdf free.Vacuum technology - Dimensions of knife-edge flanges. BS ISO 3669 This document specifies the dimensions of fixed or rotatable bolted knife- edge flanges used in vacuum systems for pressures ranging from atmospheric to as low as 10-11 Pa. There are no normative references in this document.For the purposes of this document, the following terms and definitions...
BS ISO 3862:2020 pdf free
BS ISO 3862:2020 pdf free.Rubber hoses and hose assemblies —Rubbercovered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids - Specification. BS ISO 3862 The impulse test shall be in accordance with ISO 6803 or ISO 6605. The test fluid temperature shall be 70 °C. The test fluid used shall be HFC, HFAE, HFAS or HFB as defined in ISO 6743-4.For...
BS ISO 719:2020 pdf free
BS ISO 719:2020 pdf free.Glass - Hydrolytic resistance of glass grains at 98 °C一Method of test and classification. BS ISO 719 This document specifies a> a method for determining the hydrolytic resistance of glass grains at 98 °C. The resistance is measured and expressed by the volume of acid required for titration of the alkali extracted from the unit mass...
BS ISO 1585:2020 pdf free
BS ISO 1585:2020 pdf free.Road vehicles一Engine test code一Net power. BS ISO 1585 This document specifies a method for testing engines designed for automotive vehicles. It applies to the evaluation of their performance with a view, in particular to presenting curves of power and specific fuel consumption at full load as a function of engine speed.It applies only to net power...
BS ISO 2426-1:2020 pdf free
BS ISO 2426-1:2020 pdf free.Plywood一Classification by surface appearance. BS ISO 2426-1 This document establishes general rules for the classification of plywood by its surface appearance.It concerns plywood made of hardwood including tropical and temperate hardwood, softwood and plywood derived from other lignocellulosic materials.It does not apply to overlaid plywood.The following documents are referred to in the text in such a...
BS EN 16293:2020 pdf free
BS EN 16293:2020 pdf free.Packaging - Glass Packaging - Deep BVS finishes for still wines. BS EN 16293 This document specifes dimensions of a series of deep screw finishes for the closure of wines with a COz content below 1,2 g per litre.NOTE Carbonation≥1,2 g/l CO2 requires a suitable container and closure agreed between the glass maker, closure maker and...
BS EN 16867:2020 pdf free
BS EN 16867:2020 pdf free.Building hardware - Mechatronic door furniture - Requirements and test methods. BS EN 16867 This document applies to Mechatronic door furniture (MDF) fitted on the door set which gives the possibility to control the locking and/or release part through an electronic authorization means. This can be operable by credentials (i.e. card, code, biometric).The MDF, according to...
BS EN 16905-2:2020 pdf free
BS EN 16905-2:2020 pdf free.Gas-fired endothermic engine driven heat pumps. BS EN 16905-2 This European Standard applies to GEHP appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery.The GEHP appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard....
BS EN 16307-1:2020 pdf free
BS EN 16307-1:2020 pdf free.Industrial trucks - Safety requirements and verification,Supplementary requirements for self-propelled industrial trucks, other than driverless trucks, variabl-ereach trucks and burden-carrier trucks. BS EN 16307-1 The requirements of EN ISO 3691 -1:2015, 4.7.7.1 shall apply with the following addition:Where fixed and/or removable guard systems are needed, the requirements of EN ISO 14120:2015 shall be met.When a fixed...