AS 1349-1986 pdf free.Bourdon tube pressure and vacuum gauges. AS 1349 specifies requirements for Bourdon tube pressure and vacuum gauges with circular concentric scales within the pressure range - 100 kPa to + 100 000 kPa. and the nominal size range (approximate dial diameter) 50 mm to 300 mm. Compound gauges (pressure and vacuum) are also included. The gauges are...
AS/NZS 4600:2005 pdf free
AS/NZS 4600:2005 pdf free.Cold-formed steel structures.Here is the part of the introduction: AS/NZS 4600sets out minimum requirements for the design of structural members coldformed to shape from carbon or low-alloy steel sheet, strip, plate or bar not more than 25 mm in thickness and used for load-carrying purposes in buildings. It is also applicable for structures other than buildings provided...
AS 3623-1993 pdf free
AS 3623-1993 pdf free.Domestic Metal Framing. AS 3623 sets out the performance requirements, in terms of structural adequacy and serviceability, for the framing of domestic buildings of up to two storeys in height and roof pitches of up to 35°. Alternative methods of assessing structural adequacy using either permissible stress or limit state methods are provided in Sections 2 and...
AS 1973-1993 pdf free
AS 1973-1993 pdf free.Pneumatic tyres - Passenger car, light truck, and truck/bus - Retreading and repair processes. AS 1973 sets out a code of practice for the retreading of pneumatic diagonal and radial ply tyres. including requirements for initial inspection, processing, marking and final inspection. It also sets out requirements for in-service repairs to tyres and repairs made in conjunction...
AS 3597-1993 pdf free
AS 3597-1993 pdf free.Structural and pressure vessel steel - Quenched and tempered plate. AS 3597 specifies technical requirements for the production and supply of intermediate and high-strength quenched and tempered low-alloy steel plates from a minimum thickness of 5 mm to a maximum thickness of 110 mm. It is intended for use in fusion welded structures and pressure vessels. 2...
AS 4075-1993 pdf free
AS 4075-1993 pdf free.Urea-Formaldehyde Foam Thermal Insulation - Installation Requirements For In Situ Set Foam. AS 4075 sets out recommended practice for the installation of urea-formaldehyde (UF) foam, which is manufactured and dispensed on site into the cavities of suitably constructed walls, ceilings and floors for thermal insulation purposes. This Standard defines constructions to which this application is limited. 2...
AS 3648-1993 pdf free
AS 3648-1993 pdf free.Specification and methods of test for packaged concrete mixes. AS 3648 specifies minimum requirements for the solid ingredients of dense weight concrete and for packaging appropriate proportions of these which, when mixed with water, will produce a volume of plastic concrete not exceeding 20 L (0.020 m3) from each pack. Relevant methods of test are given in...
AS 4084-1993 pdf free
AS 4084-1993 pdf free.Steel Storage Racking.Here is the introduction. AS 4084 sets out minimum requirements for the design (in permissible stress method), fabrication and erection tolerances, test methods, operation and maintenance. This Standard applies to adjustable static pallet racking made of cold-formed or hot-rolled steel structural members. It covers both the situation where racking is installed within a building and...
AS 4073-1993 pdf free
AS 4073-1993 pdf free.Urea-formaldehyde foam thermal insulation - In situ set foam. Urea-formaldehyde foam thermal insulation is produced on site and installed directly into buildings in a wet state. It dries over the following weeks. This Standard specifies the properties which such foam must meet if it is correctly formulated and produced. The foam generated in the gun shall be...
AS 4092-1993 pdf free
AS 4092-1993 pdf free.Exercise cycles - Safety requirements. AS 4092 specifies guarding and other safety requirements for all types of exercise cycles which are intended for domestic use. It does not apply to any system or assembly, part of which is a bicycle as defined in AS 1927, e.g. a trainer or simulator, nor does it apply to devices designed,...