ISO 6099:2009 pdf free.Fluid power systems and components — Cylinders — Identification code for mounting dimensions and mounting types. Introduction of ISO 6099: ISO 6099:2009 establishes a convention for the identification of mounting dimensions and types used in the mounting of fluid power cylinders. It specifies a code for identifying cylinder mounting, envelope, accessory and connector dimensions, and for cylinder...
ISO 6571:2008 pdf free
ISO 6571:2008 pdf free.Spices, condiments and herbs — Determination of volatile oil content (hydrodistillation method). 1 Scope ISO 6571 specifies a method for the determination of the volatile oil content of spices,condiments and herbs. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,...
ISO 5208:2008 pdf free
ISO 5208:2008 pdf free.Industrial valves — Pressure testing of metallic valves. Introduction of ISO 5208: The purpose of this International Standard is the establishment of basic requirements and practices for pressure testing valves of various configurations that are used in general purpose, power generation, petroleum, and petrochemical or allied industry applications. The intent is to provide a consistent set of...
ISO 62:2008 pdf free
ISO 62:2008 pdf free.Plastics — Determination of water absorption. Introduction of ISO 62: ISO 62:2008 describes a procedure for determining the moisture absorption properties in the “through-the-thickness” direction of flat or curved-form solid plastics. It also describes procedures for determining the amount of water absorbed by plastic specimens of defined dimensions, when immersed in water or when subjected to humid...
ASTM D4169-16 pdf free
ASTM D4169-16 pdf free.Standard Practice for Performance Testing of Shipping Containers and Systems. ASTM D4169 provides a uniform basis of evaluating, in a laboratory, the ability of shipping units to withstand the distribution environment. This is accomplished by subjecting them to a test plan consisting of a sequence of anticipated hazard elements encountered in various distribution cycles. This practice is...
ASTM D638-14 pdf free
ASTM D638-14 pdf free.Standard Test Method for Tensile Properties of Plastics. ASTM D638 covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed. ASTM D638 is designed to produce tensile property data for the control and specification...
ASTM B221-14 pdf free
ASTM B221-14 pdf free.Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes. This specification2 covers aluminum and aluminum-alloy extruded bars, rods, wire, profiles, and tubes in the aluminum alloys (Note 1) and tempers shown in Table 2. 4. Ordering Information 4.1 Orders for material to this specification shall include the following information: 4.1.1 This specification designation...
ASTM C33/C33M-13 pdf free
ASTM C33/C33M-13 pdf free.Standard Specification for Concrete Aggregates. ASTM C33/C33M defines the requirements for grading and quality of fine and coarse aggregate (other than lightweight or heavyweight aggregate) for use in concrete. 8. Soundness 8.1 Except as provided in 8.2 and 8.3, tine aggregate subjected to five cycles of the soundness test shall have a weighted average loss not greater...
ASTM A108-13 pdf free
ASTM A108-13 pdf free.Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished. ASTM A108 covers cold-finished carbon and alloy steel bars produced in straight length and coil to chemical compositions. Cold-finished bars are suitable for heat treatment, for machining into components, or for use in the as-finished condition as shafting, or in constructional applications, or for other similar purposes (Note...
ASTM A105/A105M-14 pdf free
ASTM A105/A105M-14 pdf free.Standard Specification for Carbon Steel Forgings for Piping Applications. This specification2 covers forged carbon steel piping components for ambient- and higher-temperature service in pressure systems. Included are flanges, fittings, valves, and similar parts ordered either to dimensions specified by the purchaser or to dimensional standards such as the MSS, ASME, and API specifications referenced in Section 2....