AS/NZS 4968.1:2003 pdf free.Heavy-road vehicles - Mechanical coupling between articulated vehicle combinations - Part1:Design criteria and selection requirements for fifth wheel, kingpin and associated equipment. This Standard sets out the attachment design forces for fifth wheel assembly and equations to determine the required D-value of components for various combinations. This Standard applies to fifth wheel assemblies used with 50 mm,...
AS 3507.1-2003 pdf free
AS 3507.1-2003 pdf free.Non-destructive testing - Part1:Guide to radiography for ferrous castings. Diagnosis of the nature of discontinuities located by radiography can only be made by consideration of both metallurgical and radiographic factors. Consideration should therefore be given to the method of manufacture of the casting under test, and the type, position and probable distribution of any discontinuities likely to...
AS 2050:2018 pdf free
AS 2050:2018 pdf free.Installation of Roof Tiles.Now download AS 2050 pdf. This Standard sets out requirements for the placement and installing of roof tiles of the types specified in AS 2049. The installation methods described in this Standard apply to tiled roofs of buildings that are intended for domestic, commercial or light industrial purposes. This Standard applies only to roofs...
BS ISO 10878:2013 pdf free
BS ISO 10878:2013 pdf free.Non-destructive testing — Infrared thermography — Vocabulary. ISO 10878:2013 defines terms used in infrared thermography for non-destructive testing and forms a common basis for standard general use. This International Standard is a compilation of terms and definitions to provide a precise understanding or interpretation of infrared thermography and thermal /infrared non-destructive testing. These serve to secure...
AS 3996:2019 pdf free download
AS 3996:2019 pdf free download.Slip Resistance Classification Of New Pedestrian Surface Materials. This Standard specifies requirements for access covers and grates for use in vehicular and pedestrian arcas. It applics to singlc or multi-part acccss covers and grates, where any single cover does not exceed 1300 mm clear opening. This Standard covers products manufactured from grey and ductile iron, cast...
AS 4586-2013 pdf free
AS 4586-2013 pdf free.Slip Resistance Classification Of New Pedestrian Surface Materials. This Standard provides means of classifying pedestrian surface materials according to their frictional characteristics when determined in accordance with the test methods set out in Appendices A, B, C, D and E. The test methods enable characteristics of surface materials to be determined in either wet or dry conditions....
ISO 4957-2018 pdf free
ISO 4957-2018 pdf free.Tool steels.Now you can download ISO 4957 pdf. This document specifies requirements for the following grades of wrought tool steels: a) non-alloy cold-work tool steels; b) alloy cold-work tool steels; c) alloy hot-work tool steels; d) high-speed tool steels. If not stated otherwise, this document applies to all types of hot-rolled, forged, cold-drawn or cold-rolled products or...
BS ISO 404:2013 pdf free
BS ISO 404:2013 pdf free.Steel and steel products - General technical delivery requirements. This International Standard specifies the general technical delivery requirements for all steel products covered by IS0 6929, with the exception of steel castings and powder metallurgical products. IS0 10474 describes the inspection documents to be used. Where the delivery requirements agreed upon for the order or specified...
BS EN 1433:2002 pdf free
BS EN 1433:2002 pdf free.Drainage Channels For Vehicular And Pedestrian Areas - Classification, Design And Testing Requirements, Marking And Evaluation Of Conformity. This European Standard specifies requirements for linear drainage channels for the collection and conveyance of surface water when installed within areas subjected to pedestrian and/or vehicular traffic. These channels are defined as either Type I, which requires no...
AS/NZS 4994.1:2009 pdf free
AS/NZS 4994.1:2009 pdf free.Temporary edge protection - Part1:General requirements. This Standard specifies requirements for the design, manufacture and testing of equipment that is intended to provide temporary edge protection for persons working on roofs of buildings having slopes not greater than 35 to the horizontal and for other exposed edges, prior to the installation of the permanent walling materials. NOTES:...