ISO PDF Download

AS NZS 60335.2.95:2020 pdf free

AS NZS 60335.2.95:2020 pdf free.Household and similar electrical appliances一Safety Part 2.95: Particular requirements for drives for vertically moving garage doors for residential use. 7.12.1 Addition: The installation instructions shall state the substance of the following: WARNING: Important safety instructions. Follow all instructions since incorrect installation can lead to severe injury. The installation instructions shall include details for the installation of...

09-01

Download

AS NZS 60335.2.96:2020 pdf free

AS NZS 60335.2.96:2020 pdf free.Household and similar electrical appliances- Safety Part 2.96: Particular requirements for flexible sheet heating elements for room heating. 7.12.101 The instructions for applications in floors of concrete or similar material or under tiles shall state that a) a grid is to be installed above the heating unit. The grid is to — be protected against corrosion...

09-01

Download

AS NZS 61058.1:2020 pdf free

AS NZS 61058.1:2020 pdf free.Switches for appliances Part 1: General requirements (IEC 61058-1:2016 (ED. 4.0) MOD). 5 General information on tests 5.1 Testing shall be performed according to the general guideline information provided in Clause 5 5.1.1 In general, the test conditions for higher ratings of a switch may represent test conditions for lower ratings. See 5.2. 5.1.2 In all...

09-01

Download

AS NZS 60929:2020 pdf free – AC and/or DC-supplied electronic control gear for tubular fluorescent lamps

AS NZS 60929:2020 pdf free.AC and/or DC-supplied electronic control gear for tubular fluorescent lamps一Performance requirements (IEC 60929:2011+AMD1:2015 CSV (ED.4.1) MOD). 4 General notes on tests 4,1 Tests according to this standard are type tests. NOTE The requirements and tolerances permitted by this standard are based on the testing of a type test sample submitted by the manufacturer for that purpose....

09-01

Download

AS NZS 60335.2.84:2020 pdf free

AS NZS 60335.2.84:2020 pdf free.Household and similar electrical appliances一Safety Part 2.84: Particular requirements for toilet appliances. 3 Terms and definitions This clause of Part 1 is applicable except as follows. 3.1 Definitions relating to physical characteristics 3.1.9 Replacement: normal operation operation of the appliance under the following conditions: Appliances are operated in cycles, each cycle being initiated every 10 mm,...

09-01

Download

AS NZS 61724.1:2020 pdf free

AS NZS 61724.1:2020 pdf free.Photovoltaic system performance Part 1: Monitoring (IEC 61724-1:2017/ MOD). 4 Monitoring system classification The required accuracy and complexity of the monitoring system depends on the PV system size and user objectives. This document defines three classifications of monitoring systems providing varying levels of accuracy, as listed in Table 1. The monitoring system classification shall be stated...

09-01

Download

AS NZS 62386.207:2020 pdf free

AS NZS 62386.207:2020 pdf free.Digital addressable lighting interface Part 207: Particular requirements for control gear一LED modules (device type 6) (IEC 62386- 207:2018 (ED. 2.0) MOD). 9.3.2 Dimming curve when IEC 62386-218 is implemented Upon accepting the instruction “SELECT DIMMING CURVE (DTRO)” according to this document, the control gear shall behave as if it accepted “SELECT DIMMING CURVE (DTRO)” as defined...

09-01

Download

AS NZS 62386.304:2020 pdf free

AS NZS 62386.304:2020 pdf free.Digital addressable lighting interface Part 304: Particular requirements一Input devices一Light sensor (IEC 62386-304:2017 (ED. 1.0) MOD). NOTE It is possible for "hysteresis BandHigh" to exceed the maximum possible “inputValue” in cases where "inputValue" is large and hysteresis is increased. Software developers can choose to limit "hysteresis BandHigh" to the maximum possible "inputValue' . Figure 2 shows an...

09-01

Download

AS ISO ASTM 52910:2020 pdf free – Additive manufacturing一Design一 Requirements, guidelines and recommendations

AS ISO ASTM 52910:2020 pdf free.Additive manufacturing一Design一 Requirements, guidelines and recommendations. 4 Purpose 4.1 This document provides requirements, guidelines and recommendations for designing parts and products to be produced by AM processes. Conditions of the part or product that favour AM are highlighted. Similarly, conditions that favour conventional manufacturing processes are also highlighted. The main elements include the following: —...

09-01

Download

AS ISO ASTM 52921:2020 pdf download – Standard terminology for additive manufacturing – Coordinate systems and test methodologies

AS ISO ASTM 52921:2020 pdf download.Standard terminology for additive manufacturing一Coordinate systems and test methodologies. build platform, n—of a machine, any base which provides a surface upon which the build is started and supported throughout the hui Ic! process (see A 1. 1). DiscussioN—The machine build platform may he solid or perforated and made from a wide variety of materials and...

09-01

Download